EMC 5050 SMD LED

#1
Feature:
●Small luminous surface, high - light output
●Good color uniformity, SDCM<5
●Full color temperature range coverage
●High reliability, high cost performance, high efficiency
●Lead-free encapsulation,compliance with RoHS
Color Temperature ColorPower(w)Current(mA) Maximum Current Luminous flux(lm)Forward voltage(v)≥explicit referenceLight effect lm/W
4000-6500pure/nature white1452001852480185
3000-3500warm white1452001652480170
4000-6500pure/nature white1602501851880185
3000-3500warm white1602501651880170
4000-6500pure/nature white1452002052470210
3000-3500warm white1452001852470190
4000-6500pure/nature white1602502001870210
3000-3500 warm white1602501801870190

● Intensity Bin Limit (IF = 45 mA)

Bin codeFlux(lm) for reference
MinMax
1175190
2190205
3205220

● VF Bin Limit (IF = 45 mA)
Bin codeMin.(V)Max.(V)
12122
22223
32324
42425


● Chromaticity CIE
●Requirements for application and reflow soldering
Reflow Soldering
Pre-heat
120~160℃
Pro-heat time
120 seconds Max.

Peak temperature
245℃ Max.

Soldering time
10 seconds Max.

Condition
Refer to Temperature-profile

After reflow soldering rapid cooling should be avoided
Temperature-profile(Surface of circuit board)
Use the following conditions shown in the figure.
<Pb-free solder>
1.Reflow soldering should not be done more than two times
2.When soldering,do not put stress on the LEDs during heating

●Handling Precautions
Compare to epoxy encapsulation that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more prone to damage by external mechanical force. As a result, Special handling precautions must be observed during assembling using silicone encapsulated LED product, Failure to comply might leads to damage and premature failure of the LED.

♦ Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or handle the silicone lens surface, it may damage the internal circuitry.

♦ Not suitable to operate in acidic environment, PH<7.

♦ LED operating environment and sulfur element composition cannot be over 25 PPM in the LED mating usage material.

When we need to use external glue for LEDs application products, please make sure that the external gluematches the LEDs packaging glue. Additionally ,as most of LEDs packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent external material from getting into the inside of LEDs, which may cause the malfunction of LEDs, the single content of Bromine
element is required to be less than 225 PPM,the single content of Chlorine element is required to be less than225PPM,the total content of Bromine element and Chlorine element in the external glue of the applicationproducts is required to be less than 375 PPM.

♦ The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top ofpackage. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should betaken to avoid the strong pressure on the encapsulated part. So when using the picking up nozzle, the pressureon the silicone resin should be proper.

♦ Static electricity or surge voltage damages the LEDs. Damaged LEDs will show some unusual characteristicssuch as the lower forward voltage, or the not light at low current, even not light. All devices, equipment andmachinery must be properly grounded. At the same time, it is recommended that wrist bands oranti-electrostatic gloves, anti-electrostatic containers be used when dealing with the LEDs.

Storage
♦ Before opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. The LEDs shouldbe used within a year.

♦ After opening the package, the product should be stored at 30℃ or less and humidity less than 10% RH, andbe soldered within 24 H. It is recommended that the product be operated at the workshop condition of 30℃or less and humidity less than 60% RH. If unused LEDs remain, they should be stored in moisture proofpackages, such as sealed containers with packages of moisture absorbent material (silica gel). It is alsorecommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bagagain.
●Reliability
(1) TEST ITEMS AND RESULTS
Type
Test Item
Ref.Standard
Test Conditions
Note
Number of Damaged

Environmental
SequenceResistance to Soldering Heat(Reflow Soldering)JESD22-B106Tsld=260℃,5sec2 times
0/100
Temperature Cycle
JESD22-A104-40℃30min ↑↓5min
100℃ 30min100 cycle
0/100
Thermal Shock
JESD22-A106-40℃15min ↑↓5min
100℃ 15min100 cycle
0/100
High Temperature Storage
JESD22-A103Ta=100℃1000 hrs
0/100
Low Temperature Storage JESD22-A119Ta=-40℃1000 hrs
0/100
Power temperature Cycling JESD22-A105On 5min -40℃>15min
↑↓ ↑↓<15min
Off5min 100℃>15min100 cycle
0/100
Operation
SequenceLife Test
老化寿命测试JESD22-A108Ta=25℃
IF=150mA1000 hrs
0/100
High Humidity Heat
Life Test
高温高湿老化测试JESD22-A10180℃RH=80%
IF=150mA1000 hrs
0/100
(2) CRITERRIA FOR JUDGING THE DAMAGE
Item
Symbol
Test Conditions
Criteria for Judgement
Min.Max
Forward Voltage
VFIF=150mA--U.S.L*)×1.1
Reverse Current
IRVR=5V--U.S.L*)×2.0
Luminous Intensity
IVIF=150mAL.S.L**)×0.7
U.S.L.:Upper Standard Level L.S.L.:Lower Standard Level
Packaging & Delivery
Packaging Details
4000pcs/reel, each reel Anti-static vacuum Bag
Delivery Time
Shipped in 3-5 days after payment

Transportion:
1. FedEx/DHL/UPS/TNT for samples/small orders, Door-to-Door;
2. By Air or by Sea for mass goods, for FCL; Airport/ Seaport receiving;
3. Customers specifying freight forwarders or negotiable shipping methods!
4.Delivery port: Shenzhen.
Our Service
●All standard products in 3 years warantty.
●Reply your inquiry in 12 working hours.
●Well-trained and experienced staffs to answer all your inquiries in fluent English.
●Strict quality control procedures before shipment.
●LED Module (PCB Disign and Mounting LEDs on PCB) customized design is available.
●Delivery the goods to our customer all over the world with speed and precision.
FAQ:
What's your Question:
1.What`s your payment way?
T/T,Paypal, Western union, visa card,L/C; Credit Car Avaliable.
2. What`s your shipment way?
Airplane, Marine shipmeng ,DHL, EMS, UPS, etc.
3.How long of your delivery time ?
within 5-7 working days to prepare the goods.
4. How long is your warranty time ?
We offer 3 years warranty.
5. What`s your main products ?
LumiS LED Specializes in high quality led from 2011, Inculding EMC 2016/3014/3020/3030 and Ceramic 3535/5050. The Power from 0.2W-10W/LED, The Voltage from 2.8V-50V/LED; CCT from 2500-20000K, also have RGBWY/UV/IR,RGBW 4in1 Hight Power Ceramic LEDs. Also we can customize your LED Module, etc.
6. Do you have any certifications for your products ?
Yes, All of led have CE,RoHS certifcations and LM-80 for our EMC Serices Products.
Company:
Patents:
Alisa Huang
Guangdong Elite Optoelectronic Technology Co., LTD
Mobilephone:+86-18033336027
Tel:0769-89080660-824
Fax:0769-89080658
Email:ruilu_sales1@elitebm.com
Contact: Carol Chen
Mobilephone:+86-13798703095
Telephone:+86-769-88941998
Email:elite1@elitebm.comEMC 5050 SMD LED
website:http://www.smd-emc-led.com/emc-led/emc-5050-smd-led/